Door control module

From W220 S-Class Encyclopedia
(Redirected from Door Control Module)
Jump to navigation Jump to search

Door control module (in WIS) or Electric Seat Adjuster Switch (in EPC) is electrical part responsible for several tasks. When looking for part in catalogs, you may need to add color code to end of the part number (e.g., A22082106587C45).

Functionality

The door control module in itself is a pretty dumb device. All key presses are sent over CANBUS to SAM. SAM then broadcasts message to all modules and module which understands the message acts appropriately (whether lighting up some bulb, engaging seat heating, moving seat, etc.).

DCM is responsible for:

  • External mirror:
    • Lighting up mirror turn signal light
    • Lighting up mirror courtesy light
    • Mirror heating
    • Mirror angle altering
    • Mirror fold-in
  • Receiving signal from infrared receiver
  • Engaging door power close
  • Opening door window
  • Receiving signal from window control switch
  • receiving signal from trunk open switch
  • Receiving signal from mirror control switch
  • Powering door handle LED
  • Powering door courtesy light
  • Receiving signal from seat regulation switch

Power for driver side front DCM is controlled by fuse X.

Location

DCM is located in door trim held by plastic clips.

Front of door control module trim.
Back of door control module trim.
DCM in door trim.

Connectors

Front left door control module connected.

Heated and/or ventilated seat buttons

Seat ventilation functionality does not depend on the specific DCM used. Appropriate buttons are not part of DCM and can be bought separately.

It is possible to use heated and ventilated button for engaging heating on vehicle without ventilation. It is possible to use heated button on vehicle with seat ventilation, however, not all heating and ventilating states can be engaged.

DCM with heating button removed.
Heated seat button for left DCM (A2208210358).
Heated seat button for right DCM (A2208210458).
Heated and ventilated seat button (A2208210558).
A2208210558 (back).
Heated and ventilated seat button (A2208210658).
A2208210658 (back).
A2208210658 dissected (front).
A2208210658 dissected (back).

Memory function

DCM with memory function.


Memory function is available in vehicles with option code 275 - MEMORY PACKAGE (DRIVER SEAT, STRG. COL., MIRROR).

The settings for the left and right exterior mirrors, the interior rearview mirror and the steering column are also stored together with the driver's seat setting.

As of 10/2003 the inside rearview mirror memory function is no longer part of the memory package.

Up to 31.05.01

  • Driver's side: For each transmitter key, two complete seat settings can be stored and called up again on the driver's side. A total of eight memory areas are available.
  • Front passenger's side: On the front passenger's side, two complete seat settings can be stored and called up again.

As of 01.06.01

  • Driver's side: For each transmitter key, three complete seat settings can now be stored and called up again on the driver's side. A total of twelve memory areas are available.
  • Front passenger's side: On the front passenger's side, three complete seat settings can now be stored and called up again.
  • Rear (only model 220 with electrically adjustable individual rear seats): Three complete seat settings can be stored and called up again.

Calling up stored positions function

Calling up stored positions (driver, front passenger)

  • 1 - CAN message: "Current storage block" (depends on ignition/starter key)
  • 2 - Actuation of the respective motors
  • 3 - Feedback of the current position
  • A67 - Inside mirror unit
  • K40/6 - Left front fuse and relay module
  • K40/6kD - Relay 1 Jacket tube longitudinal adjustment
  • K40/6kE - Relay 2 Jacket tube longitudinal adjustment
  • K40/6kI - Relay 1 Jacket tube height adjustment
  • K40/6kI - Relay 1 Jacket tube height adjustment
  • K40/6kJ - Relay 2 Jacket tube height adjustment
  • M20 - ESC [ELV] motor
  • M21/1 - Left electrically adjustable and heated exterior mirror
  • M21/2 - Right electrically adjustable and heated exterior mirror
  • M27 - Left front seat adjustment motor group with memory
  • M28 - Right front seat adjustment motor group with memory
  • N10/6 - Left front SAM control module
  • N10/6 - Left front SAM control module
  • N32/1 - Left front seat adjustment control module with memory
  • N32/2 - Right front seat adjustment control module with memory
  • N69/1 - Left front door control module
  • N69/2 - Right front door control module
  • N70 - Overhead control panel control module
  • N73 - EIS control module
  • S50/1 - Outside mirror switch with mirror fold-in/fold-out facility

Function requirements:

  • No overvoltage or undervoltage
  • Term.15R or 15 ON
  • Driver's door/front passenger's door open
  • No button for manual seat adjustment, mirror adjustment or steering column adjustment pressed
  • Normalization carried out properly

Calling up memory and Ergo positions (driver) up to 31.5.01. When calling up the memory function or Ergo function by pressing the memory 1 switch (N69/1s6), memory 2 switch (N69/1s7) or ERGONOMICS switch (N69/1s8) in the left door control module (N69/1) the positions stored in the relevant control modules are actuated:

  • Inside rearview mirror
  • Front passenger's exterior mirror
  • Steering column
  • Driver seat

The left front door control module (N69/1) recognizes that a switch is pressed and sends the following message via the CAN: "Left front memory - Assume position 1/2/Ergo". Memory 3 (N69/1s15), in the left front door control module (N69/1).

This message is received from the left front SAM control module (N10/6), from the overhead control panel control module (N70), from the right front door control module (N69/2) and from the left front seat adjustment control module with memory (N32/1).

Consequently these control modules, and also the left front door control module (N69/1), actuate the respective motors (see Figure), when the button is pressed further, until it is recognized via the local position recognitions that the stored positions are reached.

As of 1.6.01 the Ergo position is not used anymore, it is replaced by a further memory button. This memory location is called up by pressing the switch for memory 3 (N69/1s9) in the left front door control module (N69/1).

Calling up memory/Ergo positions (front passenger) up to 31.5.01. When the memory feature is called up by pressing the memory 1 switch (N69/2s6), memory 2 switch (N69/2s7) ERGONOMY switch (N69/2s9) in the right front door control module (N69/2), the positions of the front passenger's seat stored in the right front seat adjustment control module with memory (N32/2) are approached. The right front door control module (N69/2) recognizes that a switch is pressed and places the following message on the CAN: "Right front memory - Assume position 1/2/Ergo". This message is received from right front seat adjustment control module with memory (N32/2) which then, when the button is pressed further, actuates the motors of the right front seat adjustment motor group with memory (M28) until it is recognized via local position recognitions that the stored positions are reached.

As of 1.6.01 the Ergo position is not used anymore, it is replaced by a further memory button. This memory location is called up by pressing the memory 3 switch (N69/2s15) in the right front control module (N69/2).

Calling up memory positions (rear). (On model 220 with electrically adjustable individual rear seats with memory option code 224 - INDIV.REAR SEAT AND HEAD RESTRAINTS, ELEC.ADJUSTAB)

Left rear side: When the memory feature is called up by pressing the memory 1 switch (N69/3s3) or memory 2 switch (N69/4s4) or memory 3 switch(N69/3s5) in the driver's side door control module (N69/3) the positions of the left rear seat stored in the rear seats control module (N25/6) are approached.

Right rear side: When the memory feature is called up by pressing the memory 1 switch (N69/4s3) or memory 2 switch (N69/3s4) or memory 3 switch (N69/4s5) in the right rear door control module (N69/4) the respective door control module recognizes that a switch is pressed and places the following message on the CAN "Left and right rear memory - Assume position 1/2/3". This message is received by the rear seats control module (N25/6) which then, if the button is pressed further, actuates the respective adjustment motors until it is recognized via local position recognitions that the stored positions are reached.

Storing memory positions function

Function prerequisites:

  • Circuit 15R or 15 ON

Together with the storage of the driver's seat position in addition the inside rearview mirror, the outside mirror as well as the steering column position are stored in the relevant control module key-related.

Memory locations up to 31.5.01. The positions of the driver's seat and front passenger's seat including the adjustments of the multicontour backrest (special equipment) can be stored on two memory locations.

Memory locations as of 1.6.01 The positions of the driver's seat and front passenger's seat including the adjustments of the multicontour backrest (special equipment) can be stored on three memory locations.

The positions are stored in the following control modules:

Driver side:

  • Seat position: Left front seat adjustment control module with memory (N32/1)
  • Inside rearview mirror position: Overhead control panel control module (N70)
  • Left outside mirror: Left front door control module (N69/1)
  • Right outside mirror: Right front door control module (N69/2)
  • Steering column position: Left front SAM control module (N10/6)

Passenger side:

  • Seat position: Right front seat adjustment control module with memory (N32/2)

Rear seats (model 220 with electrically adjustable individual rear seats only):

  • Seat position: Rear seats control module (N25/6)

Up to 31.5.01 storing driver's seat position with associated mirror and steering column positions. The currently adjusted positions are stored by pressing the memory switch (N69/1s9) in the left front door control module (N69/1) and then within 3 seconds, the memory 1 switch (N69/1s6) or memory 2 switch (N69/1s7).

If at the same time no other switch in this switch group is pressed, the left front door control module (N69/1) sends a message to the CAN. The respective control modules receive this request for position storage and check whether valid values are supplied via local position measurements. If this is the case, the current positions are stored in the non-volatile memory.

Up to 31.5.01 storing front passenger's seat position. The currently adjusted front passenger's seat position is stored in the same way as the driver's seat position. It is triggered by pressing the memory switch (N69/2s9) in the right front door control module (N69/2) and then, within 3 seconds, memory 1 switch (N69/2s6) or memory 2 switch (N69/2s7)

Storing left rear seat position (model 220 with electrically adjustable individual rear seats only). The currently adjusted rear seat position is stored by pressing the memory switch (N69/3s10) in the left rear door control module (N69/3) and then memory switch 1 within 3 seconds (N69/3s3) or memory 2 switch (N69/3s4) or memory 3 switch (N69/3s5).

The storage process for the right rear side is analog to the left rear side. In the process the memory switch (N69/4s10) in the right rear door control module (N69/4) and memory 1 switch (N69/4s3) or memory 2 switch (N69/4s4) or memory 3 switch (N69/4s5) are used.

As of 1.6.01 revised storage process. There are two ways of storing the respective positions:

For the driver's side:

a) If the memory switch (N69/1s9) is kept pressed and additionally one of the memory 1 switches (N69/1s6), memory 2 switches (N69/1s7); memory 3 switches (N69/1s15) is pressed for t>=40 ms, the storage process is thereby concluded.

b) Press the memory switch (N69/1s9) for t=>40 ms and then release again, then within t<3 seconds, press the desired memory location via memory 1 switch (N69/1s6); memory 2 switch (N69/1s7), memory 3 switch (N69/1s15) for t>=40 ms so that the storage process is concluded.

In order to avoid faults during storage it is necessary that the voltage supply is applied to the control module for a further five seconds at least.

If during the storage process no other switch from the switch group is pressed, the values are sent from the respective door control module to the relevant control modules via the CAN. These control modules check whether the local position measurement supplies valid values. If this is the case the current positions are stored in the non-volatile memory.

The storage process for the front passenger's side is analog to the driver's side. In the process the memory 1 switch (N69/2s6), memory 2 switch (N69/2s7), memory 3 switch (N69/2s15) and memory switch (N69/2s9) are used.

Code-related storage block selection

The driver's seat position (memory feature) is stored in the left front seat adjustment control module with memory (N32/1) (vehicle with right hand steering (N32/2)) on a key-related basis.

The electronic ignition switch control module (N73) recognizes the inserted transmitter key (A8/1) and notifies the left front seat adjustment control module with memory (N32/1) (vehicles with right hand steering: right front seat adjustment control module with memory (N32/2)) which of the four memory blocks are to be activated via the CAN. One memory block consists of two memory areas. One complete seat position can be stored for each memory area. The memory area is selected via the memory 1 switch (N69/1s6)/memory 2 switch (N69/1s7) in the left front door control module (N69/1) (vehicle with right hand steering: Corresponding switches in the right front door control module (N69/2)).

Key track 1 2 5/6 3/4/7/8
Memory block number (CAN message from electronic ignition switch) 1 2 3 4
Position key on left front door control module (N69/1) 1 2 1 2 1 2 1 2
Memory area in the left front seat adjustment control module with memory (N32/1) (LHS) 1 2 3 4 5 6 7 8

Parking position for exterior rearview mirror on passenger side function

Moving the exterior rearview mirror on the passenger side to the parking position when reverse gear is engaged (illustrated on vehicle with left-hand steering)

  • 1 - CAN-message: "Shift lever position"
  • 2 - CAN-message: "Reverse gear engaged"
  • 3 - CAN-message: "Vehicle speed signal"
  • A1 - Instrument cluster
  • M21/2 - Right electrically adjustable and heated exterior rearview mirror
  • N15/5 - Electronic shift lever module control module
  • N69/1 - Left front door control module
  • N69/2 - Right front door control module
  • N73 - Electronic ignition/starter switch control module

Function prerequisites:

  • Voltage not too low or too high
  • C.15 ON
  • Reverse gear engaged
  • Exterior mirror changeover left/right switch (S50/1s3) in passenger-side rearview mirror position
  • Position measurement supplying valid values
  • "Mirror setting when parking" enabled under instrument cluster convenience settings
Enabling mirror setting when parking

Purpose of parking position. After the exterior rearview mirror on the passenger side has moved to the parking position the driver can observe the distance between the associated rear wheel and edge of the curb in the mirror when backing up to park the car.

Function. The right front door control module (N69/2) (vehicles with right-hand steering: left front door control module (N69/1) ) receives the CAN message "Reverse gear engaged", causing the exterior rearview mirror on the passenger side to be moved to the parking position stored for ignition/starter key in use.

One parking position can be stored in the right front door control module (N69/2) (vehicles with right-hand steering: left front door control module (N69/1)) per ignition/starter key.

Termination of function. The exterior rearview mirror is automatically moved back to the original position when:

  • The transmission is shifted to a forward gear, after expiration of a time of approx. 10s
  • or the vehicle speed increases to about 10 km/h or
  • the exterior mirror changeover left/right switch (S50/1s3) in the exterior mirror adjustment switch with mirror fold-in/out feature (S50/1) on the left front door control module (N69/1) (vehicles with right-hand steering: right front door control module (N69/2)) has been actuated.

The mirror is also moved back to the original position even when it was adjusted manually in the parking position with the adjustment switch.

Storing parking position for exterior rearview mirror function

Function prerequisites:

  • C. 15R or c.15 ON
  • Vehicle speed v=0 km/h

The parking position for the exterior mirror on the passenger side can be stored in relation to the key with the left front door control module (N69/1) (vehicles with right-hand steering: right front door control module (N69/2)).

For this purpose it is first necessary to adjust the rearview mirror to the desired parking position manually with the mirror adjustment switches in the exterior mirror adjustment switch group with mirror fold-in/out feature (S50/1).

Then press the memory switch (N69/1s9) (vehicles with right-hand steering: (N69/2s9)), and within 3 seconds the bottom half of the rocker switch of the exterior mirror adjustment up/down switch (S50/1s1). When this combination of buttons is pressed the left front door control module (N69/1) transmits the CAN message "Store parking position" to the right front door control module (N69/2) (vehicles with right-hand steering: vice versa). The momentary exterior rearview mirror position is then stored as the parking position.

Ergonomics default setting function

Function requirements:

  • No overvoltage or undervoltage
  • Term. 15R
  • Circuit 15 ON
  • Respective vehicle door open
  • Normalization carried out properly

Ergo default setting: Finding the individual driver's/front passenger's seat position is made easier with the Ergo default setting. By assuming the Ergo position of the driver's seat in addition the left and right outside mirrors, the inside rearview mirror, steering column and multicontour backrest (special equipment) are preset. Once the default setting is complete only a fine adjustment is necessary.

Calling up Ergo positions (driver's side):

The Ergo default settings:

  • of the left front seat adjustment motor group with memory (M27) (vehicle with left hand steering)
  • of the right front seat adjustment motor group with memory (M28) (vehicle with right hand steering)
  • of the left electrically adjustable and heated outside mirror (M21/1)
  • of the right electrically adjustable and heated outside mirror (M21/2)
  • of the inside rearview mirror unit (A67)
  • of the steering column adjustment motors (M20) are dependent on the driver's seat longitudinal position

Driver's side Ergo default setting is carried out as follows on vehicle with left hand steering: First the longitudinal position of the seat is adjusted individually using the switch for fore/aft front seat adjustment (N69/1s1) in left front door control module (N69/1). The Ergo function is then triggered by pressing the ERGONOMY (N69/1s8) switch. The respective motors are now actuated corresponding to the ergonomics maps stored in the control modules for as long as the switch remains pressed and the limit position is not yet reached. Here the Ergo default setting is made via the corresponding switches in the right front door control module (N69/2).

Calling up Ergo positions (front passenger's side) with left-hand steering: On the front passenger's side when the ERGONOMY switch is pressed (N69/2s8) in the right front door control module, (N69/2) the motors of the right front seat adjustment motor group with memory (M28) are actuated corresponding to the ergonomics maps stored in the right front seat adjustment control module with memory (N32/2). The actuation also takes place here depending on the longitudinal position of the seat. Right-hand steering: Here the Ergo default setting is made via the corresponding switches in the left front door control module (N69/1).

Retrofitting memory function

It seems that at least facelift W220 comes with seats/mirrors that support memory function. The only missing part to enable memory function is DCM with memory buttons. Even more, installing switch board with buttons from DCM that has them will allow to use memory function without the need for the whole DCM replacement.

For example, it has been tested that vehicle originally equipped with DCM A2208214179 in drivers doors can be replaced with DCM A2208211579 and memory seats will work out of the box. To mount DCM with memory buttons into the doors, the door panel with holes for memory buttons must also be retrofitted.

Window control switch

Driver's door switch

For facelift vehicles driver's doors have part number A2208213179 (for both left hand and right hand drive vehicles). Although visually the same EPC lists part A2208213279 for vehicles equipped with remote trunk locking (option code 881).

A2208213179 Window control switch (facelift) from driver's door.

Override switch

You can disable the following functions in the rear passenger compartment for instance when you have children riding in the rear passenger compartment):

  • rear door window operation
  • adjustment of front passenger seat from the rear (option code 247)
  • cigarette lighter in rear

To activate slide override switch (1) to the right. A dot becomes visible. The functions in the rear are disabled.

Note: Operation of the rear door windows with the switches located in the driver's door is still possible.

Trunk lid switch

You can open the trunk from the inside if the vehicle is stationary. Pull remote trunk lid switch (2) until trunk begins to open. The trunk lid opens. The indicator lamp (1) comes on and remains lit until the trunk is closed.

You can close the trunk from the inside if the vehicle is equipped with option code 881. To close press remote trunk lid switch (2) until the indicator lamp (1) goes out and trunk lid is closed.

Other door switch

In all doors except driver's door, the switch with part number A2208213379 is used.

A2208213379 Window control switch (facelift) from all door's except driver's door.

Using right hand drive DCM in left hand drive vehicle

It has been tested that RHD DCM A2208212179 installed on left side of LHD vehicle originally equipped with A2208214179 will work fine, however, the mirror controlling switch will not work and window controlling switch will be able open only driver's door window. Similarly, RHD DCM A2208211879 installed on left side of LHD vehicle originally equipped with A2208214979 will work fine, however, the window opening switch will open left side driver's door window.

Using left DCM on the right side

The physical location of DCM is programmed into DCM. E.g., if left DCM is connected to right side, the DCM will still move left seat.

Using pre-facelift DCM in facelift vehicle

Has not been tested.

Using rear DCM with seat adjustment in vehicle without adjustable seats

It has been tested that installing A2208212879 in vehicle without adjustable rear seat the DCM can be used to control front seat. The heating/ventilation buttons when pressed blink for a second and switch off probably signaling that heated/ventilated rear seats not installed. The problem with this upgrade is that DCM cover with holes for this DCM is not available with for short wheel base models, hence self made holes in the cover must be made.

List of door control modules

Early DCM had weak protection against moisture and therefore could be easily damaged if the door window was left open while raining. In later DCMs MB has improved protection against moisture. When looking for replacement DCM buy the latest compatible DCM in the category.

Facelift (from 30/09/2002)

Front Left

Part No. Front Back
A2208214179 (left hand drive vehicles) photo photo
A2208211579, option 275 (left hand drive vehicles) with memory photo photo
A2208214479 (right hand drive vehicles) photo photo
A2208212179 (right hand drive vehicles) with memory photo photo

Front Right

Part No. Front Back
A2208214979 (left hand drive vehicles) photo photo
A2208211679 (left hand drive vehicles) with memory photo photo
A2208215079 (right hand drive vehicles)
A2208211879 (right hand drive vehices) with memory photo photo

Rear Left

Part No. Front Back
A2208216279 photo photo
A2208215779, option 402/872 photo photo
A2208212379, option 223/223+402/223+872 photo photo
A2208212779, option 223+247/223+247+402/223+247+872 (right hand drive vehicles) photo photo
A2208212579, option 224/224+402/224+872, with memory photo
A2208216979, option 224+247/224+247+402/224+247+872 (right hand drive vehicles) with memory photo photo

Rear Right

Part No. Front Back
A2208216879 photo photo
A2208216379, option 402/872 photo photo
A2208212479, option 223/223+402/223+872 photo photo
A2208212879, option 223+247/223+247+402/223+247+872 (left hand drive vehicles) photo photo
A2208212679, option 224+247/224+402/224+872, with memory photo photo
A2208217079, option 224+247/224+247+402/224+247+872 (left hand drive vehicles) with memory photo photo


Pre-facelift (to 01/09/2002)

Front Left

Part No. Front Back
A2208208710 (left hand drive vehicles, to date 29/07/1999, replaced by A2208218751) photo
A2208218751 (left hand drive vehicles, to date 30/06/2011) photo photo
A2208212958 (left hand drive vehicles, from date 30/06/2001 to date 01/09/2002)
A2208200110 (left hand drive vehicles, to date 29/07/1999, replaced by A2208219351) photo photo
A2208219351 (left hand drive vehicles, to date 30/06/2001) photo photo
A2208213358 (left hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo
A2208208910 (right hand drive vehicles, to date 30/06/2001, replaced by A2208219151) photo
A2208219151 (right hand drive vehicles, to date 30/06/2001) photo photo
A2208213158 (right hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo
A2208202610 (right hand drive vehicles, to date 30/06/2001, replaced by A2208219751) photo photo
A2208219751 (right hand drive vehicles, to date 30/06/2001) photo photo
A2208213758 (right hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo

Front Right

Part No. Front Back
A2208208810 (left hand drive vehicles, to date 30/06/2001, replaced by A2208219251) photo photo
A2208219251 (left hand drive vehicles, to date 30/06/2001) photo photo
A2208213258 (left hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo
A2208200210 (left hand drive vehicles, to date 30/06/2011, replaced by A2208219851) photo photo
A2208219851 (left hand drive vehicles, to date 30/06/2011) photo photo
A2208213858 (left hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo
A2208209010, (right hand drive vehicles, to date 29/06/1999, replaced by A2208218851) photo photo
A2208218851, (right hand drive vehicles, to date 01/09/2002) photo photo
A2208202710 (right hand drive vehicles, to date 30/06/2011, replaced by A2208219451) photo photo
A2208219451 (right hand drive vehicles, to date 30/06/2011) photo photo
A2208213458 (right hand drive vehicles, from date 30/06/2001 to date 01/09/2002) photo photo

Rear Left

Part No. Front Back
A2208214351, (to date 30/06/2001, replaced by A2208211558) photo photo
A2208211558, (to date 30/06/2001, replaced by A2208214958) photo photo
A2208214958 photo photo
A2208203310, option 402/872 (to date 30/06/2011, replaced by A2208210958) photo photo
A2208210958, option 402/872 (to date 30/06/2011, replaced by A2208214758) photo photo
A2208214758, option 402/872 photo photo
A2208200310, option 223/223+402/223+872 (to date 30/06/2011, replaced by A2208211358) photo photo
A2208211358, option 223/223+402/223+872 (to date 30/06/2011, replaced by A2208215158) photo photo
A2208215158, option 223/223+402/223+872 photo photo
A2208214551, option 223+247/223+247+402/223+247+872 (right hand drive vehicles, replaced by A2208218351) photo photo
A2208218351, option 223+247/223+247+402/223+247+872 (right hand drive vehicles, replaced by A2208215558) photo
A2208215558, option 223+247/223+247+402/223+247+872 (right hand drive vehicles) photo photo
A2208211158, option 224/224+402/224+872 (to 30/06/2011, replaced by A2208215358) with memory photo
A2208215358, option 224/224+402/224+872, with memory
A2208218551, option 224+247/224+247+402/224+247+872 (right hand drive vehicles, to 30/06/2011, replaced by A2208215758), with memory
A2208215758, option 224+247/224+247+402/224+247+872 (right hand drive vehicles), with memory

Rear Right

Part No. Front Back
A2208214451 (to 30/06/2001, replaced by A2208211658) photo photo
A2208211658 (to 30/06/2001, replaced by A2208215058) photo photo
A2208215058 photo photo
A2208203410, option 402/872 (to 30/06/2001, replaced by A2208211058) photo photo
A2208211058, option 402/872 (to 30/06/2001, replaced by A2208214858) photo photo
A2208214858, option 402/872 photo photo
A2208200410, option 223/223+402/223+872 (to 30/06/2001, replaced by A2208211458) photo photo
A2208211458, option 223/223+402/223+872 (to 30/06/2001, replaced by A2208215258) photo photo
A2208215258, option 223/223+402/223+872 photo photo
A2208214651, option 223+247/223+247+402/223+247+872 (left hand drive vehicles, replaced by A2208218451) photo photo
A2208218451, option 223+247/223+247+402/223+247+872 (left hand drive vehicles, replaced by A2208215658) photo photo
A2208215658, option 223+247/223+247+402/223+247+872 (left hand drive vehicles) photo photo
A2208211258, option 224+247/224+402/224+872 (to 30/06/2001, replaced by A2208215458) with memory photo
A2208215458, option 224+247/224+402/224+872, with memory
A2208218651, option 224+247/224+247+402/224+247+872 (left hand drive vehicles, to 30/06/2001, replaced by A2208215858) with memory photo
A2208215858, option 224+247/224+247+402/224+247+872 (left hand drive vehicles) with memory photo

Resources

Replacing DCM (pre-facelift).
Front door panel removal (facelift).
Mirror light woes caused by faulty DCM.
Replace Door Control Module (By Masood)

Making your own DCM control buttons: http://www.benzworld.org/forums/w220-s-class/1624796-seeking-rh-headrest-adjuster-button.html

Wiring

Right front door control module (N69/2)

1 (CAN and power):

  • 1 (brown) - Ground right footwell (W36/1)
  • 2 (red/black) - Fuse 39 in the right fuse box (F1/1)
  • 3 - CAN-B L
  • 4 - CAN-B H
  • 5 -
  • 6 -

2 (Right front power window motor M10/4):

  • 1 (red) - FH T pin 3 of M10/4
  • 2 (black) - FH H pin 6 of M10/4
  • 3 (brown/white) - H (-) pin 1 of M10/4
  • 4 (green) - (+) pin 4 of M10/4
  • 5 (blue) - H Sig.1 pin 5 of M10/4
  • 6 (yellow) - H Sig.2 pin 4 of M10/4

3 (Right front door entrance and exit lamp E17/4 and Right front door inside handle illumination E17/12):

  • 1 (brown/yellow) - (-) pin 2 of E17/12
  • 2 (brown/green) - AL (-) pin 1 of E17/4
  • 3 (red/yellow) - AL (+) pin 2 of E17/4
  • 4 (green/purple) - (+) pin 1 of E17/12

4 (Mirror):

  • 1 (black/red) - SH (+) of M21/2r1 (Mirror heater)
  • 2 (brown) - SH (-) of M21/2r1 (Mirror heater)
  • 3 (black) - M21/2m2 (Mirror in/out adjustment motor) and M21/2m1 (Mirror up/down adjustment motor)
  • 4 (green) - M21/2m1 (Mirror up/down adjustment motor)
  • 5 (white) - M21/2m2 (Mirror in/out adjustment motor)
  • 6 (brown) - BL (-) of E6/6 (Right exterior mirror turn signal lamp)
  • 7 (pink) - BL (+) of E6/6 (Right exterior mirror turn signal lamp)
  • 8 (yellow) - M21/2m3 (Mirror fold-in motor)
  • 9 (green) - M21/2m3 (Mirror fold-in motor)
  • 10 (brown/white) - M21/2e1 (Right outside mirror ambient lamp)

5 (Mirror):

  • 1 (blue) - (-) end of M21/2r2 (Mirror up/down adjustment potentiometer) and M21/2r3 (Mirror in/out adjustment potentiometer)
  • 2 (yellow/white) - wiper of M21/2r2 (Mirror up/down adjustment potentiometer)
  • 3 (yellow/green) - wiper of M21/2r3 (Mirror in/out adjustment potentiometer)
  • 4 (red) - (+) other end of M21/2r2 (Mirror up/down adjustment potentiometer) and M21/2r3 (Mirror in/out adjustment potentiometer)
  • 5 - NC
  • 6 (brown/black) - M21/2e1 (Right outside mirror ambient lamp)
  • 7 (purple) - M21/2h1 (Automatic dimming mirror)
  • 8 (pink) - M21/2h1 (Automatic dimming mirror)
  • 9 - NC
  • 10 - NC

12 (Exterior mirror switch with mirror fold-in/fold-out facility S50/1):

  • 1 -
  • 2 -
  • 3 -
  • 4 -
  • 5 -
  • 6 -

Dissecting DCM (A2208214979)

Left-hand-drive right front DCM (without memory function) dissected. The process of disassembling did not cause damage - all parts pictured can be reassembled back.

Case front.
Case front (inside).
Case back.
Case back (inside).
Circuit board (front).
Circuit board (back).
Switch board (front).
Switch board (back).
Buttons (front).
Buttons (back).
LED contour (front).
LED contour (back).

Dissecting DCM (A2208211679)

Left-hand-drive right front DCM (with memory function) dissected. The process of disassembling did not cause damage - all parts pictured can be reassembled back.

Case front.
Case front (inside).
Case back.
Case back (inside).
Circuit board (front).
Circuit board (back).
Switch board (front).
Switch board (back).
Buttons (front).
Buttons (back).
LED contour (front).
LED contour (back).

DAS adaptations (DCM-FL)

Adaptations available in DAS for door control module front left (A2208211579).

List of adaptations.
Triggering threshold of excessive force limiter for power window mechanism.
Touch function for folding mirror in.
Touch function with immediate reversal.
S86/1 (Left front lock switch).
Mirror memory.
Actuate folding outside mirrors.
Convenience feature through component A26/1 (front left IR receiver unit).
Convenience feature through component S86/1 (Left front lock switch).
Fault memory entry B1521-03 if mirror housing adjustment was faulty.
Window power cutoff delay.
Automatic lowering on light-armored vehicles.
Power window emergency operation.
Coding Duration of actuation "Mirror housing adjustment".

DAS adaptations (DCM-FR)

Adaptations available in DAS for door control module front left (A2208214979).

Adaptations missing from front passenger side DCM:

  • Touch function for fold in mirror in
  • Touch function with immediate reversal
  • Coding Duration of actuation "Mirror housing adjustment"
List of adaptations.

DAS actuations (DCM-FL)

Actuations available in DAS for door control module front left (A2208211579).

Mirror manual adjustment.
Mirror programmed adjustment.