Fuel pump filter

From W220 S-Class Encyclopedia
Jump to navigation Jump to search


Fuel pump and filter is mounted on the left frame floor in front of the rear axle.

  • M3 - Fuel pump
  • 55/1 - Fuel filter with integrated fuel pressure regulator approx. 3.8 bars


Fuel Pump

Illustration shows screw spindle pump

  • M3 - Fuel pump


The task of the pump is to supply an adequate quantity of fuel to the fuel system at the required pressure in all driving states.

On model W220 helical spindle pump is mounted at frame floor.


Illustration shows screw spindle pump

  • 1 - Rotating spindle
  • 2 - Drive spindle
  • 3 - Check valve
  • 4 - Pressure relief valve
  • 5 - Electric motor
  • 6 - Ground connection
  • 7 - Voltage supply
  • a - Fuel from the fuel tank
  • b - Fuel to the fuel filter

The fuel pump (M3) pumps more fuel than the engine requires in total in order to maintain the pressure in the fuel system in all operating states. As a result of this circulation, relatively cool fuel is available at all times for injection (avoids the formation of vapor bubbles). A pressure relief valve (4) is integrated in the fuel pump in order to limit the pressure.

The check valve (3) in the fuel pump decouples the fuel system from the fuel tank by preventing fuel from flowing back through the fuel pump to the fuel tank. The fuel pump is actuated by the engine control unit through the fuel pump relay.

Parts

To date: 30/06/2001 (screw connections):

  • A0004707894 (EUR 370)

From date: 30/06/2001 (with pluggable connections):

  • A0014701294 (EUR 370)
  • BOSCH 0986580354 (EUR 173)
  • PIEBURG 7.28126.51.0 (EUR 155)
  • TOPRAN 401632 (EUR 95)
  • STARKE 162-029 (EUR 30)

Part number for pluggable electrical connector on vehicle side - A1685452728. The male part of the pluggable electrical connector is TRUCKTEC/29.3086 (useful to convert fuel pump with screw connections to pluggable connection).

Fuel pump female connector (A1685452728)
Fuel pump male connector (TRUCKTEC/29.3086)

Filter

The task of the fuel filter is to filter impurities out of the fuel, maintaining constant fuel pressure in wide limits irrespective of the fuel pump delivery.

  • 55/1 - Fuel filter with integrated fuel pressure regulator
  • CAN - Pressurization line
  • PUMP - Feed from fuel pump
  • TANK - Return flow to fuel tank
  • MOT - To engine


  • 55/1 - Fuel filter with integrated fuel pressure regulator
  • 55/3 - Valve
  • 55/5 - Diaphragm (membrane)
  • 55/6 - Compression (push) spring
  • 55/9 - Filter element insert
  • 55/40 - Diaphragm pressure regulator
  • A - Feed from fuel pump
  • b - Diaphragm pressure regulator vent line
  • B - Fuel return flow to fuel tank
  • C - Fuel pressure connection to engine

The fuel filter consists of a sheet metal casing with an integrated filter element (55/9). The fuel flows through this from the outside to the inside. As a result any impurities are trapped.

The diaphragm pressure regulator (55/40) controls the fuel pressure of approx. 3.8 bar (operating pessure) via the fuel return flow quantity to the fuel tank.

If the set fuel pressure is exceeded, the diaphragm (55/5) is pushed against the push spring (55/6) and the valve (55/3) attached to the diaphragm opens the passage for the fuel return to the fuel tank (B). If the set pressure is below the limit, the valve is closed again by means of the push spring.

Fuel pressure as a function of the fuel pump delivery
  • A - Fuel pressure in bar
  • B - Fuel pump delivery in liters per hour

A greatly varying fuel pump delivery (e.g. 20 or 140 l/h) does not have any great effect on the fuel pressure.

Parts

  • A0024773001 OE (EUR 85)
  • MANN-FILTER WK 720 (EUR 60)
  • Blue Print ADA102301 (EUR 15)

Testing fuel pressure

Remove Schrader valve cap from the fuel rail fuel pressure port and connect your fuel pressure tester. Be extremely careful during this test procedure as if fuel falls on hot engine parts it may cause a fire. Never carry this test if the engine is hot.

The fuel pressure should build up as soon as you turn on the ignition before you even try to crank the engine and the pressure should not drop after turning on the ignition. The pressure reading should be around 3.8 bars. If the pressure is not maintained then the cause can be either a faulty fuel filter or a faulty fuel pump.

Fuel pressure reading 3.8 bars

Fuel pump and filter replacement

Fuel pump with hose clamps