Pushbutton Control Module (N22): Difference between revisions

From W220 S-Class Encyclopedia
Jump to navigation Jump to search
(Created a new section for Pushbutton Control Module (N22))
 
mNo edit summary
Line 6: Line 6:
The small blower fan called the Aspirator, which draws cabin air over the ACC Air Temperature Sensor (N22/b1) in the Pushbutton Control Module (N22) can become noisy due to excessive build up of dust. The solution is to clean it. See [[Access and Cleaning - In Cabin Air Temperature Sensor (N22/b1)]]
The small blower fan called the Aspirator, which draws cabin air over the ACC Air Temperature Sensor (N22/b1) in the Pushbutton Control Module (N22) can become noisy due to excessive build up of dust. The solution is to clean it. See [[Access and Cleaning - In Cabin Air Temperature Sensor (N22/b1)]]


==Removal and Dismantle - Pushbutton Control Module (N22)==
==DIY Removal and Dismantle - Pushbutton Control Module (N22)==
These steps describe the method used to remove and dismantle the ACC Pushbutton Control Module (N22). N22 houses the Air Temperature Sensor (N22/b1) which may then be removed for testing, repaired or replaced and also the aspirator may be cleaned.
These steps describe the method used to remove and dismantle the ACC Pushbutton Control Module (N22). N22 houses the Air Temperature Sensor (N22/b1) which may then be removed for testing, repaired or replaced and also the aspirator may be cleaned.
* Ensure Parking Brake is engaged.
# Ensure Parking Brake is engaged.
* Place Transmission Selector in Drive.
# Place Transmission Selector in Drive.
* Remove two Torx screws holding Ash Tray to Front Panel.
# Remove two Torx screws holding Ash Tray to Front Panel.
[[File:003 W220 Remove Ash Tray Torx Screws.JPG|300px|center]]
#: [[File:003 W220 Remove Ash Tray Torx Screws.JPG|300px|center]]
* Slide Ash Tray from its housing.
# Slide Ash Tray from its housing.
[[File:004 W220 Remove Ash Tray.JPG|300px|center]]
#: [[File:004 W220 Remove Ash Tray.JPG|300px|center]]
* Remove Ash Tray cable connector.
# Remove Ash Tray cable connector.
* Place Ash Tray to one side.
# Place Ash Tray to one side.
* Slide ACC Pushbutton Control Module out of its housing.
# Slide ACC Pushbutton Control Module out of its housing.
[[File:005 W220 Remove ACC Pushbutton Control Module.JPG|300px|center]]
#: [[File:005 W220 Remove ACC Pushbutton Control Module.JPG|300px|center]]
* Slide the white locking lever on the cable connector to one side to release the connector.
# Slide the white locking lever on the cable connector to one side to release the connector.
[[File:006 W220 ACC Pushbutton Control Module Housing.JPG|300px|center]]
#: [[File:006 W220 ACC Pushbutton Control Module Housing.JPG|300px|center]]
* Place ACC Pushbutton Control Module on suitable Workbench.
# Place ACC Pushbutton Control Module on suitable Workbench.
[[File:007 W220 ACC Pushbutton Control Module.JPG|300px|center]]
#: [[File:007 W220 ACC Pushbutton Control Module.JPG|300px|center]]
* Remove two Torx screws holding ACC Pushbutton Control Module Front Panel in place.
# Remove two Torx screws holding ACC Pushbutton Control Module Front Panel in place.
[[File:008 W220 ACC Pushbutton Control Module with Front Panel Removed.JPG|300px|center]]
#: [[File:008 W220 ACC Pushbutton Control Module with Front Panel Removed.JPG|300px|center]]
* Press in two release tabs on underside while prising the join line with a suitable tool.
# Press in two release tabs on underside while prising the join line with a suitable tool.
[[File:009 W220 ACC Pushbutton Control Module Showing Two Underside Release Tabs.JPG|300px|center]]
#: [[File:009 W220 ACC Pushbutton Control Module Showing Two Underside Release Tabs.JPG|300px|center]]
* Press in two release tabs on topside while prising the join line with a suitable tool.
# Press in two release tabs on topside while prising the join line with a suitable tool.
[[File:010 W220 ACC Pushbutton Control Module Showing Two Topside Release Tabs.JPG|300px|center]]
#: [[File:010 W220 ACC Pushbutton Control Module Showing Two Topside Release Tabs.JPG|300px|center]]
* Open the ACC Pushbutton Control Module.
# Open the ACC Pushbutton Control Module.
[[File:011 W220 ACC Pushbutton Control Module Separated.JPG|300px|center]]
#: [[File:011 W220 ACC Pushbutton Control Module Separated.JPG|300px|center]]
* Note the location of the Aspirator Sub Module on the RH side.  The Aspirator Shroud is best removed after removing the internally mounted printed circuit board.
# Note the location of the Aspirator Sub Module on the RH side.  The Aspirator Shroud is best removed after removing the internally mounted printed circuit board.
[[File:012 W220 ACC Pushbutton Control Module Aspirator Sub Module.JPG|300px|center]]
#: [[File:012 W220 ACC Pushbutton Control Module Aspirator Sub Module.JPG|300px|center]]
* Lever the five tabs on the housing to release one side of the internally mounted pcb.
# Lever the five tabs on the housing to release one side of the internally mounted pcb.
[[File:013 W220 ACC Pushbutton Control Module Showing Five Tabs.JPG|300px|center]]
#: [[File:013 W220 ACC Pushbutton Control Module Showing Five Tabs.JPG|300px|center]]
* Remove the internally mounted pcb from its housing and then the Aspirator Shroud can be removed from the printed circuit board.
# Remove the internally mounted pcb from its housing and then the Aspirator Shroud can be removed from the printed circuit board.
[[File:014 W220 ACC Pushbutton Control Module Aspirator Housing Removed.JPG|300px|center]]
#: [[File:014 W220 ACC Pushbutton Control Module Aspirator Housing Removed.JPG|300px|center]]
* Remove the three Torx screws securing the small RH pcb.
# Remove the three Torx screws securing the small RH pcb.
[[File:015 W220 ACC Pushbutton Control Module RH Small PCB.JPG|300px|center]]
#: [[File:015 W220 ACC Pushbutton Control Module RH Small PCB.JPG|300px|center]]
* Open the small RH pcb to reveal the ACC Pushbutton Control Module Thermistor.
# Open the small RH pcb to reveal the ACC Pushbutton Control Module Thermistor.
[[File:016 W220 ACC Pushbutton Control Module Thermistor on RH Small PCB.JPG|300px|center]]
#: [[File:016 W220 ACC Pushbutton Control Module Thermistor on RH Small PCB.JPG|300px|center]]
* Reassemble in reverse order.
# Reassemble in reverse order.


==Resistance Specification - Sensor N22/b1 in Pushbutton Control Module (N22)==
==Resistance Specification - Sensor N22/b1 in Pushbutton Control Module (N22)==

Revision as of 06:37, 16 December 2017

Issues - Pushbutton Control Module (N22)

Failed Air Temperature Sensor (N22/b1)

The Auto Climate Control (ACC) Air Temperature Sensor (N22/b1) in the Pushbutton Control Module (N22) often fails and causes the ACC to malfunction. This is easily diagnosed by utilising the ACC Hidden Menu Feature (See Automatic Climate Control (ACC) Service Menus which allows an access/review/read of the ACC actual parameter values during normal operation. Parameter NR.00: In Car Temperature Sensor (N22/b1), ACC Pushbutton Control Module (N22) Front Compartment should indicate the in cabin air temperature, eg 25C. If it reads 0C and the cabin is not freezing then there is a fault. The solution is to test the thermistor and aspirator function and then if necessary replace it. See Testing - In Cabin Air Temperature Sensor (N22/b1). To rteplace it see section Removal and Dismantle - Pushbutton Control Module (N22) below.

Aspirator Noise

The small blower fan called the Aspirator, which draws cabin air over the ACC Air Temperature Sensor (N22/b1) in the Pushbutton Control Module (N22) can become noisy due to excessive build up of dust. The solution is to clean it. See Access and Cleaning - In Cabin Air Temperature Sensor (N22/b1)

DIY Removal and Dismantle - Pushbutton Control Module (N22)

These steps describe the method used to remove and dismantle the ACC Pushbutton Control Module (N22). N22 houses the Air Temperature Sensor (N22/b1) which may then be removed for testing, repaired or replaced and also the aspirator may be cleaned.

  1. Ensure Parking Brake is engaged.
  2. Place Transmission Selector in Drive.
  3. Remove two Torx screws holding Ash Tray to Front Panel.
  4. Slide Ash Tray from its housing.
  5. Remove Ash Tray cable connector.
  6. Place Ash Tray to one side.
  7. Slide ACC Pushbutton Control Module out of its housing.
  8. Slide the white locking lever on the cable connector to one side to release the connector.
  9. Place ACC Pushbutton Control Module on suitable Workbench.
  10. Remove two Torx screws holding ACC Pushbutton Control Module Front Panel in place.
  11. Press in two release tabs on underside while prising the join line with a suitable tool.
  12. Press in two release tabs on topside while prising the join line with a suitable tool.
  13. Open the ACC Pushbutton Control Module.
  14. Note the location of the Aspirator Sub Module on the RH side. The Aspirator Shroud is best removed after removing the internally mounted printed circuit board.
  15. Lever the five tabs on the housing to release one side of the internally mounted pcb.
  16. Remove the internally mounted pcb from its housing and then the Aspirator Shroud can be removed from the printed circuit board.
  17. Remove the three Torx screws securing the small RH pcb.
  18. Open the small RH pcb to reveal the ACC Pushbutton Control Module Thermistor.
  19. Reassemble in reverse order.

Resistance Specification - Sensor N22/b1 in Pushbutton Control Module (N22)

Refer to section Resistance Specification - In Cabin Air Temperature Sensor which applies to both In Cabin Air Temperature Sensors ie Sensor N22/b1 which is in Pushbutton Control Module (N22) and Sensor N70/b1 which is in Overhead Control Panel N70. The OEM sensors were found to be not identical in appearance although their electrical properties were very similar.

  • Sensor N22/b1 which is in Pushbutton Control Module (N22),
Retrieved from "https://w220.wiki/index.php?title=Pushbutton_Control_Module_(N22)&oldid=6993"