Steering linkage: Difference between revisions

From W220 S-Class Encyclopedia
Jump to navigation Jump to search
mNo edit summary
No edit summary
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
==Description - Steering Linkage==
See also [[front axle]] page for other suspension parts at front.
Edit required.


==Parts - Steering Linkage==
== Part numbers ==
Edit required.


==Issues - Steering Linkage==
[[File:W220_steering_linkage_epc.png|thumb|none|Steering linkage-related parts in [[EPC]].]]
http://www.benzworld.org/forums/w220-s-class/1684021-s-class-rack-pinion-steering-problems.html


==DIY Procedures - Steering Linkage==
* Tie Rod outer left/right: A2303300203 (Lemforder 2115402 (EUR 45))
* Tie Rod inner left/right: A2203380715 (Lemforder 2115302 (EUR 12))
 
{|
|[[File:W220_inner_tie_rod_Lemforder_2115302.jpg|thumb|none|Inner tie rod (Lemforder 21153 02)]]
|[[File:W220_outer_tie_rod_Lemforder_2115402.jpg|thumb|none|Outer tie rod (Lemforder 21154 02)]]
|}
 
 
== DIY Repairs ==
 
=== Check track rod and drag link linkage for play, check rubber boots ===
<!-- AP46.00-P-4653F, Check track rod and drag link linkage for play, check rubber boots, 2.7.13 -->
 
{|
|
* 1g - Bellows
* 10 - Tie rod
* 10l - Tie rod end
|[[File:W220_tie_rod.png]]
|[[File:W220_tie_rod_bellow.png]]
|}
 
# Switch off ignition
# Check boots (1g). Never check the boot (1) by pressing in or around the ribs. This will cause damage to the plastic and then result in leakage. Raise vehicle at front axle. Stretch bellows by turning the steering to the left and right while checking for damage (cracks, chafing marks and dents). If damaged, the boot (1g) must be replaced.
# Check tie rod ball joint for play. Inspect tie rod joints by pulling and pushing firmly. In event of play on tie rod ball joint the tie rod (10) is to be replaced.
# Check rubber boots of tie rod ends (10l) for signs of leaks and condition. If a rubber boot leaks replace tie rod (10).
 
=== Remove/install track rod ===
<!--
AR46.40-P-0200I, Remove/install track rod, 27.9.97
MODEL 203 (except 203.081 /084 /087 /092 /281 /284 /287 /292)
MODEL 209
MODEL 215
MODEL 220 (except 220.083 /084 /087 /183 /184 /187)
MODEL 230
-->
 
Shown on model 220
{|
|
* 10 - Tie rod
* 10a - Tie rod joint
* 10f - Locknut
|[[File:W220_remove_install_track_rod.jpg]]
|}
 
# Remove front wheel
# Pry off tie rod joint (10a) from steering knuckle assembly. Installation: Replace self-locking nut.
# Release locknut (10f) and unscrew track rod (10). Counterhold tie rod (10) for loosening the jam nut (10f) (arrow).
# Install in the reverse order
# Perform chassis alignment ([[Wheel_alignment#DIY_toe-in_measurement|wheel toe-in alignment]])
 
Torque specifications:
* Self-locking nut, tie rod to steering knuckle: 1st stage: 50 Nm, Stage 2: 60°
* Lock nut, tie rod to inner tie rod: 60 Nm
 
{|
|[[File:W220_outer_tie_rod_right_installation.jpg|thumb|none|Installation of outer right tie rod]]
|[[File:W220_outer_tie_rod_right_installed.jpg|thumb|none|Outer right tie rod installed]]
|}
==== Pressing out and attaching track rod joint at steering knuckle ====
<!-- AR46.40-P-0200-02I, Pressing out and attaching track rod joint at steering knuckle -->
 
Shown on model 220
{|
|[[File:W220_pushing_off_track_rod_joint.jpg|300px]]
|[[File:W220_pressing_out_tie_rod_left.jpg|300px]]
|[[File:W220_pressing_out_tie_rod_right.jpg|300px]]
|}
 
 
# Pushing off: Undo self-locking nut of tie rod joint (10a).
# Mount thrust piece (045).
# Pry off tie rod joint (10a) using puller (044). Puller (044) 220589003300 with press 163589034300 for model 215, 220, 230 without code (P99) Special model "AMG Black Series". Do not damage boot, otherwise lubricant would leak out of the tie rod joint (10a) This results in increased wear.
# Remove puller (044) and thrust piece (045).
# Install: Clean tapered connection. Grease or oil must not be present at the cone and thread, as otherwise the tie rod joint (10a) could work its way loose.
# Replace self-locking nut and tighten. Counter ball head with an Allen wrench if necessary.
 
=== Remove/install inner tie rod with axial joint ===
<!-- AR46.40-P-0201I, Remove/install inner tie rod with axial joint, 9.1.06
MODEL 203, 209, 215.375 /376 /378, 220.026 /028 /063 /065 /070 /075 /125 /128 /165 /170 /175 /176 /178, 230 (except 203.08 /09 /28 /29)
-->
 
Shown on model 220
{|
|[[File:W220_Remove_inner_tie_rod_with_axial_joint.jpg]]
|}
 
# Remove front wheel
# ''Turn steering wheel to the side that is being worked on''
# Remove tie rod
# Remove bellows
# Counter gear rack (arrow). Use open end wrench (width across flats 27 mm).
# Remove inner track rod with axial joint (12). Do not use force (hammer blows, severe leverage), use open wrench (012).
# Install in the reverse order
 
Torque specification:
* Inner track rod with axial joint to rack-and-pinion joint: 110 Nm
 
{|
|[[File:W220_tie_rod_inner_outer_lemforder.jpg|thumb|none|Lemforder inner (21153 02) and outer (21154 02) tie rod]]
|[[File:W220_inner_tie_rod_joint_lemforder.jpg|thumb|none|Joint of inner tie rod (Lemforder)]]
|}
{|
|[[File:W220_tie_rod_inner_outer_right.jpg|thumb|none|Inner tie rod installed]]
|[[File:W220_tie_rod_inner_right_removal.jpg|thumb|none|Unscrewing inner tie rod from power steering]]
|}
 
 
{|
|{{#ev:youtube|https://www.youtube.com/watch?v=r_9dXHZZER8|320|left|Changing the inner tie rods on a W211|frame}}
|}
 
=== Check and replace rubber boot ===
<!-- AR46.40-P-0400I, Check and replace rubber boot, 22.2.07
MODEL 203 (except 203.081 /084 /087 /092 /281 /284 /287 /292)
MODEL 209
MODEL 215
MODEL 220.025 /026 /028 /063 /065 /070 /073 /074 /075 /125 /126 /128 /165 /170 /173 /174 /175 /176 /178 /179 /875 /878
MODEL 230 -->
 
Shown on model 220
{|
|
* 10 - Tie rod
* 10f - Jam nut
* 11 - Bellows
* 11a - Inner clamp
* 11b - Outer clamp
* 23k - O-ring
|[[File:W220_check_replace_rubber_boot.jpg]]
|}
 
'''Checking:'''
Check left and right boot (11). Never check bellows (11) by pressing in or around the plastic bead. This results in damage to the bellows (11) and causes leaks. Perfect sealing of the bellows is absolutely vital for correct functioning of the rack-and-pinion steering, so perform the visual inspection as follows: Raise vehicle at front axle. Stretch the bellows (11) by turning the steering through left and right lock and in the process check for damage (cracks, chafing marks and intrusions) and replace if necessary.
 
'''Remove/install:'''
# Detach lower engine compartment paneling (Vehicles with gasoline engine)
# Remove bottom section of soundproofing (Vehicles with diesel engines)
# Remove track rod (10)
# Unscrew lock nut (10f)
# Detach outer clamp (11b)
# Detach inner clamp (11a)
# Pull off bellows (11). Installation: Replace O-ring (23k).
# Check steering rack and inner tie rod thrust joint for corrosion and play.
## If the steering is leaking and the steering rack is already corroded, the rack-and-pinion steering must be replaced complete, in order to guarantee a satisfactory function.
## In order to guarantee satisfactory operation of the steering, the inner tie rod should be replaced when the axial joint is worn.
# Install in the reverse order
 
==== Detaching and attaching inner clamp ====
<!-- AR46.40-P-0400-01GH, Detaching and attaching inner clamp -->
# Remove: Remove inner clamping collar (11a) with side-cutting pliers.
# Install: Fit new inner hose clamp (11a) and tension with commercially available clamp pliers.
# Check that inner hose clamp (11a) is seated correctly.
 
{|
|[[File:W220_detaching_attaching_tie_rod_boot_inner_clamp.png]]
|[[File:W220_tie_rod_inner_installed_zip_tie.jpg|thumb|none|As an alternative to hose clamp a zip tie can be used.]]
|}
 
=== Locate noises from the steering ===
<!-- AR46.00-P-2000A, Locate noises from the steering, 10.11.11
MODEL all
-->
 
Example shown on model 204
{|
|
* 1 - Clamp pliers with microphone
* 2 - Cable
|[[File:W220_locate_noises_steering.jpg]]
|}
 
Example shown on model 211 front axle
{|
|
* 2 - Cable
* 3 - Selection switch
|[[File:W220_locate_noises_steering_steps.jpg]]
|}
 
# Attach clamp pliers with microphone (1).  Attach the clamp pliers as close as possible to suspect components. For evaluation purposes (normal noise - defect noise) listen to the same components, e.g compare noise from left supporting ball joint with right supporting ball joint. Up to 6 clamp pliers with microphone can be attached. Attach clamp pliers so that while driving the freedom of movement of chassis components is not impaired. Warning! It is essential to check whether the clamp pliers impair the steering function. Risk of accident! Ultrasonic leak detector and Noise diagnosis
# Fasten line (2) of clamp pliers with microphone (1) (arrows). Fasten the lines with velcro strip, cable ties or adhesive tape. Route the lines so that while driving the freedom of movement of the chassis components is not impaired.
# Guide line (2) of clamp pliers with microphone (1) into the interior. Route the lines so that contact with the road is ruled out. Route lines so that damage by a door or window is ruled out.
# Connect line (2) to the selection switch (3). The lines and connectors on the selection switch are color coded. Note the color assignment of components which are to be listened to.
# Carry out road test for noise diagnosis. Warning! Only carry out road test with a second person present. The headphones must not be worn by the driver.
# Locate defective components by listening to the microphone. Danger! Reduce the volume before each channel change otherwise hearing can be damaged If necessary: Replace faulty components.

Latest revision as of 03:32, 1 November 2020

See also front axle page for other suspension parts at front.

Part numbers

Steering linkage-related parts in EPC.
  • Tie Rod outer left/right: A2303300203 (Lemforder 2115402 (EUR 45))
  • Tie Rod inner left/right: A2203380715 (Lemforder 2115302 (EUR 12))
Inner tie rod (Lemforder 21153 02)
Outer tie rod (Lemforder 21154 02)


DIY Repairs

Check track rod and drag link linkage for play, check rubber boots

  • 1g - Bellows
  • 10 - Tie rod
  • 10l - Tie rod end
  1. Switch off ignition
  2. Check boots (1g). Never check the boot (1) by pressing in or around the ribs. This will cause damage to the plastic and then result in leakage. Raise vehicle at front axle. Stretch bellows by turning the steering to the left and right while checking for damage (cracks, chafing marks and dents). If damaged, the boot (1g) must be replaced.
  3. Check tie rod ball joint for play. Inspect tie rod joints by pulling and pushing firmly. In event of play on tie rod ball joint the tie rod (10) is to be replaced.
  4. Check rubber boots of tie rod ends (10l) for signs of leaks and condition. If a rubber boot leaks replace tie rod (10).

Remove/install track rod

Shown on model 220

  • 10 - Tie rod
  • 10a - Tie rod joint
  • 10f - Locknut
  1. Remove front wheel
  2. Pry off tie rod joint (10a) from steering knuckle assembly. Installation: Replace self-locking nut.
  3. Release locknut (10f) and unscrew track rod (10). Counterhold tie rod (10) for loosening the jam nut (10f) (arrow).
  4. Install in the reverse order
  5. Perform chassis alignment (wheel toe-in alignment)

Torque specifications:

  • Self-locking nut, tie rod to steering knuckle: 1st stage: 50 Nm, Stage 2: 60°
  • Lock nut, tie rod to inner tie rod: 60 Nm
Installation of outer right tie rod
Outer right tie rod installed

Pressing out and attaching track rod joint at steering knuckle

Shown on model 220


  1. Pushing off: Undo self-locking nut of tie rod joint (10a).
  2. Mount thrust piece (045).
  3. Pry off tie rod joint (10a) using puller (044). Puller (044) 220589003300 with press 163589034300 for model 215, 220, 230 without code (P99) Special model "AMG Black Series". Do not damage boot, otherwise lubricant would leak out of the tie rod joint (10a) This results in increased wear.
  4. Remove puller (044) and thrust piece (045).
  5. Install: Clean tapered connection. Grease or oil must not be present at the cone and thread, as otherwise the tie rod joint (10a) could work its way loose.
  6. Replace self-locking nut and tighten. Counter ball head with an Allen wrench if necessary.

Remove/install inner tie rod with axial joint

Shown on model 220

  1. Remove front wheel
  2. Turn steering wheel to the side that is being worked on
  3. Remove tie rod
  4. Remove bellows
  5. Counter gear rack (arrow). Use open end wrench (width across flats 27 mm).
  6. Remove inner track rod with axial joint (12). Do not use force (hammer blows, severe leverage), use open wrench (012).
  7. Install in the reverse order

Torque specification:

  • Inner track rod with axial joint to rack-and-pinion joint: 110 Nm
Lemforder inner (21153 02) and outer (21154 02) tie rod
Joint of inner tie rod (Lemforder)
Inner tie rod installed
Unscrewing inner tie rod from power steering


Changing the inner tie rods on a W211

Check and replace rubber boot

Shown on model 220

  • 10 - Tie rod
  • 10f - Jam nut
  • 11 - Bellows
  • 11a - Inner clamp
  • 11b - Outer clamp
  • 23k - O-ring

Checking: Check left and right boot (11). Never check bellows (11) by pressing in or around the plastic bead. This results in damage to the bellows (11) and causes leaks. Perfect sealing of the bellows is absolutely vital for correct functioning of the rack-and-pinion steering, so perform the visual inspection as follows: Raise vehicle at front axle. Stretch the bellows (11) by turning the steering through left and right lock and in the process check for damage (cracks, chafing marks and intrusions) and replace if necessary.

Remove/install:

  1. Detach lower engine compartment paneling (Vehicles with gasoline engine)
  2. Remove bottom section of soundproofing (Vehicles with diesel engines)
  3. Remove track rod (10)
  4. Unscrew lock nut (10f)
  5. Detach outer clamp (11b)
  6. Detach inner clamp (11a)
  7. Pull off bellows (11). Installation: Replace O-ring (23k).
  8. Check steering rack and inner tie rod thrust joint for corrosion and play.
    1. If the steering is leaking and the steering rack is already corroded, the rack-and-pinion steering must be replaced complete, in order to guarantee a satisfactory function.
    2. In order to guarantee satisfactory operation of the steering, the inner tie rod should be replaced when the axial joint is worn.
  9. Install in the reverse order

Detaching and attaching inner clamp

  1. Remove: Remove inner clamping collar (11a) with side-cutting pliers.
  2. Install: Fit new inner hose clamp (11a) and tension with commercially available clamp pliers.
  3. Check that inner hose clamp (11a) is seated correctly.
As an alternative to hose clamp a zip tie can be used.

Locate noises from the steering

Example shown on model 204

  • 1 - Clamp pliers with microphone
  • 2 - Cable

Example shown on model 211 front axle

  • 2 - Cable
  • 3 - Selection switch
  1. Attach clamp pliers with microphone (1). Attach the clamp pliers as close as possible to suspect components. For evaluation purposes (normal noise - defect noise) listen to the same components, e.g compare noise from left supporting ball joint with right supporting ball joint. Up to 6 clamp pliers with microphone can be attached. Attach clamp pliers so that while driving the freedom of movement of chassis components is not impaired. Warning! It is essential to check whether the clamp pliers impair the steering function. Risk of accident! Ultrasonic leak detector and Noise diagnosis
  2. Fasten line (2) of clamp pliers with microphone (1) (arrows). Fasten the lines with velcro strip, cable ties or adhesive tape. Route the lines so that while driving the freedom of movement of the chassis components is not impaired.
  3. Guide line (2) of clamp pliers with microphone (1) into the interior. Route the lines so that contact with the road is ruled out. Route lines so that damage by a door or window is ruled out.
  4. Connect line (2) to the selection switch (3). The lines and connectors on the selection switch are color coded. Note the color assignment of components which are to be listened to.
  5. Carry out road test for noise diagnosis. Warning! Only carry out road test with a second person present. The headphones must not be worn by the driver.
  6. Locate defective components by listening to the microphone. Danger! Reduce the volume before each channel change otherwise hearing can be damaged If necessary: Replace faulty components.